352 Empire Blvd.,
Rochester, NY 14609
Phone: 585-482-7850
Fax: 585-654-9295
findit@danscraftsandthings.com
COVERLITE DK.GREEN 19X36
COVERLITE DK.GREEN 19X36

COVERLITE DK.GREEN 19X36

Model ID: COVQ1807
DAN'S Price: $7.99
 
This is Dark Green CoverLite Iron-On White Synthetic Tissue Covering from Coverite. A strong, tough, synthetic material to replace tissue and dope.

Ideal for covering lightweight or Park Flyer models up to 50".
Extremely light weight of only .89 ounce per square yard (28g per square meter).

CoverLite is sealed to a model with heat, and is factory "doped" with a totally fuelproof resin. It is not only resistant to glow and diesel fuel, but is also airproof and waterproof. Very easy to apply to a model with Coverite Balsarite.
Stronger and more puncture-resistant than normal doped tissue, and paintable with Coverite 21st Century spray paint.
Comes folded in a bag (5"x 5.5") with a hangable header card.

REQUIRES: Preapplying Fabric Balsarite Adhesive (COVR2500) onto the surface to be covered, and then applying heat to tighten the covering. Miscellaneous covering tools.

Length: 36" (915mm)
Width: 19.5" (495mm)
Weight: 1 oz/sq yd (28 g/sq m)

COMMENTS:
Preparation before using CoverLite Covering:
Fill all cracks and hollows. Sand all parts to be covered to remove bumps or unevenness which would show through the covering. Wipe away all sanding residues. There are two methods of applying CoverLite, depending on whether the part being covered is an open framework or is a solid surface, such as sheet balsa.

Method #1, Open Framework:
With a small piece of plastic sponge apply a very thin coat of Balsarite to the framework. Pay particular attention to the outer edges (leading and trailing edges are longerons). Areas of sheet balsa should be coated all over. Allow the Balsarite to dry (15-30 minutes). Cut a panel of CoverLite at least 1" (25mm) larger all around the framework to be covered and lay the CoverLite on the framework. Set your iron between 195-212F (90-100C) and tack the Coverlite in place at a few points around the edges, using the toe of the iron. While tacking, gently pull the CoverLite to get a smooth fit without wrinkles. Do not try to get the CoverLite drum tight, just smooth and wrinkle-free. Reheating and peeling back while hot allows the CoverLite to be repositioned. Then seal the Coverlite all around the edges of the frame with the iron. Trim excess from around the edge with a sharp blade and reseal the edges. Where panels of CoverLite meet and overlap, the overlap has to be coated with Balsarite (and dried) so it can be ironed down. It is best to apply this Balsarite with a fine brush BEFORE trimming away any excess.

Method #2, Solid Surfaces: Solid surfaces such as sheet balsa, ply and veneer. With a scrap of moistened plastic sponge, apply a thin coat of Balsarite all over the surface to be covered. Cut a panel of CoverLite oversize and tape it down on a smooth surface and apply a very thin coat of Balsarite. Allow to dry. Place the coated side of the CoverLite onto the coated surface and iron down with a cool iron (about 195F, 90C). Start at the center and iron outward toward the edges to avoid trapping air under the CoverLite. If the CoverLite wrinkles around the iron, lower the iron temperature. CoverLite can be contoured around slight double curves by heating and gently pulling. For large area of double curvature, it is easiest to cut the CoverLite into "fingers" which are ironed down in succession.

send to a friend send to a friend   print notes print notes
Powered by iCAM32
E-Commerce/POS Software


SSL